Types of Controls

Thermostatic Radiator Valves (TRV)

Thermostatic radiator valves do not control the boiler; they reduce the flow of water through the radiator which they are fitted to when the temperature goes above a certain setting. Set them to the level you want for the room; a lower setting uses less energy and so will save you money.
We do not recommend using radiator covers because TRVs sense the air temperature around them and control the flow rate depending on what level they're set at. Having a cover over the radiator means the TRV is enclosed, which is likely to make it think that the room temperature is higher than it actually is.
If you already have a radiator cover that cannot be removed, then it is still worth using TRVs to control the temperature as much as possible. If you feel the radiator is not hot enough at a particular setting, you can turn up the TRV.

Hot Water Thermostat

If your hot water is stored in a cylinder, the thermostat will prevent it becoming hotter than it needs to. Once the water has reached the temperature you have set, the heat supply from the boiler will be turned off.
Turning the thermostat higher will not make the water heat up any faster, and the water heating will not come on if a time switch or programmer has switched it off.
Cylinder thermostats are usually fitted between one quarter and one third of the way up the cylinder. They have temperature scales marked; you should set them at between 60 and 65 degrees. This is hot enough to kill harmful bacteria in the water, but it’s also hot enough to scald. For extra safety consider installing a thermostatic mixing valve which will automatically ensure that hot water is at a safe temperature.
If you have a combi boiler then you won’t have a cylinder, but there will probably be a hot water thermostat on the boiler itself. This is often a dial with a picture of a tap on it.

Boiler Thermostat

Your boiler will usually have a dial on it, marked in numbers or from Min to Max. This sets the temperature of the water that will be pumped from the boiler through the radiators. The higher this is set, the quicker it will heat your home. In fact, if it is not set high enough when it is very cold outside your home may not reach the desired temperature. However, condensing boilers work more efficiently when the water returning to the boiler is below 55 degrees, so it can be better not to set the temperature too high.
If you have a regular boiler with separate hot water cylinder, your boiler thermostat should always be set to a higher temperature than the cylinder thermostat, otherwise the hot water cylinder will never get up to temperature. If you have a combi boiler you will probably have two dials – the one with a radiator symbol controls the output to the radiators and you can set this at the best point for your heating without it affecting the hot water temperature.

Automatic Boiler Thermostat

Weather compensation

​

When the weather is cold you need your boiler stat to be set to a high level to make sure your house can get warm enough. If the weather is milder you could turn the boiler stat down and still be warm enough. This will make the system more efficient, especially if you have a condensing boiler. A weather compensator does this for you automatically by measuring the outside temperature and adjusting the boiler thermostat temperature as required.

​

Load compensation

​

When your heating first comes on the house may be very cold, especially when the weather is cold. You will want your boiler stat to be set high so that your house can heat up reasonably quickly. But if the house is fairly warm and you only need to raise it by a couple of degrees, you could risk overheating the house by heating the radiators up to full, which will then continue heating the house after it has reached the temperature you want. A load compensator measures the difference between the internal temperature and the set temperature of the thermostat and adjusts the boiler thermostat as appropriate to avoid overheating.

Boiler Interlock

This is not a control but a system of wiring that turns the boiler off when neither the room thermostat nor the cylinder thermostat needs it. Without this, the boiler can continue to ‘cycle’ and waste energy.

Programmer

This will automatically switch your heating off when you’re not at home, or when you don’t need it, such as when you’re in bed.
Programmers allow you to set ‘on’ and ‘off’ time periods. Most models will let you set the central heating and domestic hot water to go on and off at different times. There may also be manual overrides. Check that the timer on the programmer is correct before you set your programmes. You may also need to adjust it when the clocks change.
Choose a cold evening and time how long it takes for your house to warm up to a comfortable temperature – this is the warm-up time. Then turn the heating off completely and time how long it takes for the house to start to get uncomfortably cold – this is the cool-down time.
You can now set your timers including the warmup and cool down time. For example, you can make sure that the heating goes on with a warm-up time before you wake up and turns off before you leave the house. If you insulate your home, it will warm up faster and cool down more slowly and hold the heat more efficiently, so you’ll save money on heating.
Set your water to heat up only when you need it. If your hot water cylinder or tank is well insulated, you may even find that the hot water supply in the morning stays hot enough to use in the evenings.

Zone Control

Most households want to heat different rooms at different times of the day. You can do this by turning individual radiators on and off at different times, but lots of people don’t get round to these.
Zone control does this for you automatically by having separate heating circuits for different parts of the house, with a separate programmer for each circuit. If you’re fitting a new heating system, then you may want to consider zone control to help you keep heating costs down. And if you’re fitting it in a large house, you may be required to have two separate zones to meet the regulations.
If you’re not fitting a new system, it may be impractical to convert your existing pipework. In this case you want to consider programmable TRVs.

Programmable TRVs

These are temperature controls for individual radiators, just like standard TRVs, but with timing control as well. So, you can set each radiator to come on at different times, and heat each room only when you want to.

Optimisation

An optimiser works out how long it takes your house to heat up and turns the heating on at the right time so your house will be up to temperature just in time for when you need it. For example, if you get up at 7:30 in the morning you can set your programmer to 7:30am, and your thermostat to whatever you choose, and the optimiser will work out when to fire up the boiler so the house is up to the temperature you set by 7:30am. In colder weather, it will fire up earlier and in milder weather it will wait a bit, saving you energy and money.
Optimisation is one of several features that may be available if you fit a smart heating control system.

Automation

An automated heating control system works out whether and when to turn the heating on based on whether there is anyone in the building, or whether you are approaching the building. It may use sensors in the home, or it may track your phone’s location to decide when to turn the heating on. Automation is available as part of some smart heating controls, and generally includes an optimisation function to help decide when to turn the heating on.